What is New in IPv6

written by: Gerry Dawson; article published: year 2007, month 09;


In: Categories » Electronics and communication » Protocols » What is New in IPv6

IPv6 is an evolution of IPv4. The protocol is installed as a software upgrade in most devices and operating systems. If you buy up-to-date hardware and operating systems, IPv6 is usually supported and needs only activation or configuration. Currently available transition mechanisms allow the step-by-step introduction of IPv6 without putting the current IPv4 infrastructure at risk.

Here is an overview of the main changes

Extended address space

The address format is extended from 32 bits to 128 bits. This provides an IP address for every grain of sand on the planet. In addition, it also allows for hierarchical structuring of the address space in favor of optimized global routing.

Autoconfiguration

Perhaps the most intriguing new feature of IPv6 is its Stateless autoconfiguration mechanism. When a booting device in the IPv6 world comes up and asks for its network prefix, it can get one or more network prefixes from an IPv6 router on its link. Using this prefix information, it can autoconfigure for one or more valid global IP addresses by using either its MAC identifier or a private random number to build a unique IP address. In the IPv4 world, we have to assign a unique IP address to every device, either by manual configuration or by using DHCP. Stateless autoconfiguration should make the lives of network managers easier and save substantial cost in maintaining IP networks. Furthermore, if we imagine the number of devices we may have in our homes in the future that will need an IP address, this feature becomes indispensable. Imagine reconfiguring your DHCP server at home when you buy a new television! Stateless autoconfiguration also allows for easy connection of mobile devices, such as a mobile phone or handheld, when moving to foreign networks.


Simplification of header format

The IPv6 header is much simpler than the IPv4 header and has a fixed length of 40 bytes. This allows for faster processing. It basically accommodates two times 16 bytes for the Source and Destination address and only 8 bytes for general header information.


Improved support for options and extensions

IPv4 integrates options in the base header, whereas IPv6 carries options in so-called extension headers , which are inserted only if they're needed. Again, this allows for faster processing of packets. The base specification describes a set of six extension headers, including headers for routing, Mobile IPv6, and quality of service and security.

legal disclaimer

1) Our website is not responsible for the information contained by this article as well for any and all copyright infringements by authors and writers. E-articles is a free information resource. If you suspect this article for any copyright infringements, please read the Terms of service and contact us to investigate the problem.
2) The E-articles directory team is not responsible for inaccuracies, falsehoods, or any other types of misinformation this tutorial may contain and will not be liable for any loss or damage suffered by a user through the user's reliance on the information gained here. Please read the Terms of service

Useful tools and features

Translate this article to...    Send this article to you or to a friend

Link to this article from your page   
If you like this article (tutorial), please link to it from your web page using the information above. Linking to this page, this is the only way to help us improve our service, the same time providing your visitors with a way to improve their online experience.

related articles

1. Detecting Unauthorized 802.11 Cards and Access Points
The first goal is detection. Can we tell when someone powers on a card within range of the local network? This can be done with off-the-shelf components and free software. The Cisco Aironet driver included with the more recent Linux kernels supports "RF Monitor" mode, which permits promiscuous monitoring of 802.11 packets - specifically, monitoring raw 802.11 frames to detect if there are any telltale frames broadcast by a rogue access point or card. As outlined in the original 802.11 specification, ther...

2. The HTTP Request and Response Codes
The HTTP protocol can be likened to a conversation based on a series of questions and answers, which we refer to respectively as HTTP requests and HTTP responses. The contents of HTTP requests and responses are easy to read and understand, being near to plain English in their syntax. This section examines the structure of these requests and responses, along with a few examples of the sorts of data they may contain. The HTTP Request After opening a connection to the intended serv...

3. INFRASTRUCTURE PROTOCOLS AND APPLICATIONS
H.323 H.323 defines packet standards for terminal equipment and services for multimedia communications over local and wide area  networks  communicating  with  systems  connected  to telephony networks such as ISDN. The initial version of this standard  came from the International Telecommunications Union (ITU) in June 1996. It  defines  communication over IP-based local area networks (LANs). A later version (v2), adopted in January 1998, extended it over wide are...

4. Wireless IN Services
The IN protocols and concepts can be used to implement enhanced wireless services rapidly and to have these services available across serving areas in an untethered wireless network. Some of these services are listed below: Voice-Based User Identification. This service employs a form of automatic speech recognition to validate the identity of the speaker. Access to services can then be restricted to the user whose voice (phrase) has been used to train the recognition device. Voice-Based Featur...

5. Wireless LAN and Personal Area Network
The Wireless Internet is not just wireless communications across town or the country. It is also local—sometimes in a home or office building. Wireless LANs are just becoming popular with economically  priced  wireless  Ethernet  equipment.  Standards such as IEEE 802.11, HiperLAN2, and Home RF are leading the way to untethered communications in-building or outside over small areas. Another important development is the Personal Area Network, also known as Bluetooth. Let’s take a look at each of th...

6. The Domain Concept
The solution to all of these problems is the network domain. In a domain, you only have a single name and password, which gets you into every shared PC and printer on the network. Everyone's account information resides on a central computer called a domain controllera computer so important, it's usually locked away in a closet or a data-center room. A domain controller keeps track of who is allowed to log on, who is logged on, and what each person is allowed to do on the network. When you log onto the domain with your PC,...

7. Duplexing Techniques in Wireless communication systems
Wireless communication systems have evolved through several stages of multiple-access control. The foremost controllable resource has always been the frequency spectrum. Other resources such as time, code, and space were initially manipulated in a very precarious and, therefore, ineffective manner. The early systems operated in the simplex mode in the forward link. Halfduplex systems soon appeared, in which forward link and reverse link shared the same channel. Access control was performed on a push-to-talk basis wit...