How to use an ATAPI Zip or SuperDisk Drive as the boot device

written by: Grace Nelson; article published: year 2006, month 12;


In: Categories » Computers and technology » Storage devices » How to use an ATAPI Zip or SuperDisk Drive as the boot device

To configure your system to boot from an ATAPI Zip Drive or SuperDisk Drive, take the following steps:

Restart the system and enter BIOS Setup (usually by pressing F1, F2, or the Delete key while the BIOS boot screen is visible).

Verify that your high-capacity FDD is displayed as a connected device in the IDE configuration section. Most recent motherboards list the drive by name, but some older motherboards may list it only as an ATAPI device.

In BIOS Setup, locate the Boot Sequence setting (probably in the BIOS Features or Advanced Settings section) and view the available options. If an option corresponds directly to your drive (e.g., "SuperDisk Drive" or "LS-120" for the SuperDisk Drive or "Zip Drive" for the Zip Drive), set the first boot device to that option. If the BIOS provides a named boot option only for the Zip Drive but you have a SuperDisk Drive (or vice versa), try lying to the BIOS. We've never done that, but some readers have reported success using that method.

If neither drive is listed by name, but the BIOS offers an option such as "ATAPI Device/Drive," "Floptical Drive," "Removable Device/Drive," or "UHD Floppy," set the first boot device to that option. If none of these options appears, your motherboard probably does not support booting from a high-capacity FDD. Check the motherboard maker's web site for a BIOS update. Downloading and installing that update may add extended boot support to your motherboard.

After you configure Boot Sequence to use the high-capacity FDD as the first boot device, use BIOS Setup to disable the embedded FDD controller and to set Floppy Drive A: and Floppy Drive B: to "Not Installed." Save all changes and power down the system.

Insert a blank formatted disk in the drive and use the appropriate operating system commands to transfer system files to the disk and make it bootable. For a Zip Drive, you must use a Zip disk. For a SuperDisk Drive, you may use either a standard 3.5-inch 1.44 MB floppy diskette or a SuperDisk disk. Restart the system with the bootable disk in the drive. The system should boot normally to the FDD. If it doesn't, recheck your BIOS Setup configuration. Once you have verified that the system boots properly from the FDD, don't forget to restart the system and use BIOS Setup to change the boot order if you prefer to use something other than the FDD as the primary boot device.

legal disclaimer

1) Our website is not responsible for the information contained by this article as well for any and all copyright infringements by authors and writers. E-articles is a free information resource. If you suspect this article for any copyright infringements, please read the Terms of service and contact us to investigate the problem.
2) The E-articles directory team is not responsible for inaccuracies, falsehoods, or any other types of misinformation this tutorial may contain and will not be liable for any loss or damage suffered by a user through the user's reliance on the information gained here. Please read the Terms of service

Useful tools and features

Translate this article to...    Send this article to you or to a friend

Link to this article from your page   
If you like this article (tutorial), please link to it from your web page using the information above. Linking to this page, this is the only way to help us improve our service, the same time providing your visitors with a way to improve their online experience.

related articles

1. Subcodes
Subcode bytes enable the drive to find songs (which are confusingly also called tracks) along the spiral track and also contain or convey additional information about the disc in general. The subcode bytes are stored as 1 byte per frame, which results in 98 subcode bytes for each sector. Two of these bytes are used as start block and end block markers, leaving 96 bytes of subcode information. These are then divided into eight 12-byte subcode blocks, each of which is assigned a letter designation PW. Each subcode channel can hol...

2. High Capacity Magnetic Storage Devices
High-capacity removable media drives are an ever-shrinking category. With competition at the low end (1GB and under capacities) from USB flash memory keychain drives and at higher capacities from external mini-hard disks (4GB and up), rewritable DVD (8.5GB), and larger USB and FireWire hard disks (20GB and up), there are only two current product families, both from Iomega: Zip. Flexible media, with capacities of 100MB, 250MB, and 750MB REV. Rigid media, with capacity of 35GB (native...

3. Handling CD Read Errors
Handling errors when reading a disc was a big part of the original Red Book CD standard. CDs use parity and interleaving techniques called cross-interleave Reed-Solomon code (CIRC) to minimize the effects of errors on the disk. This works at the frame level. When being stored, the 24 data bytes in each frame are first run through a Reed-Solomon encoder to produce a 4-byte parity code called "Q" parity, which then is added to the 24 data bytes. The resulting 28 bytes are then run though another encoder that uses a different scheme...

4. Floppy Drive Types
As distinct from diskette types and formats, six drive types have been installed in PC-compatible systems: 5.25-inch 160/180 KB (SSDD) Single-Sided, Double-Density(SSDD) was the standard FDD in very early PC-class systems. These drives read and write only SSDD diskettes. 5.25-inch 320/360 KB (DSDD) Double-Sided, Double-Density(DSDD) was the standard FDD in PC-class systems, and was often found as a second FDD in early AT and 386 systems. The...

5. How to choose a Tape Backup Drive
Choosing a tape backup drive can be a simple job if you need to back up a single standalone system with a relatively small hard drive. The decision becomes more complex if the system has a larger hard drive or if you must back up a desktop system as well as a laptop. Choosing a tape backup drive type can be an even more complex program if you must back up a network server's hard drives and perhaps even back up the workstations from the server. As you ponder which backup tape drive you should select, consider the following facto...

6. DVD Copy Protection
DVD video discs employ several levels of protection that are mainly controlled by the DVD Copy Control Association (DVD CCA) and a third-party company called Macrovision. This protection typically applies only to DVD-Video discs, not DVD-ROM software. So, for example, copy protection might affect your ability to make backup copies of The Matrix, but it won't affect a DVD encyclopedia or other software application distributed on DVD-ROM discs. Note that every one of these protection systems has been broken, so with a lit...

7. How to Manually Resolve Motherboard Conflicts
In the past, the only way to resolve conflicts manually was to take the cover off your system and start changing switches or jumper settings on the adapter cards. Fortunately, this is a bit easier with plug-and-play because all the configuration is done via the Device Manager software included in the operating system. Although some early plug-and-play cards also had jumper switches or setup options to enable them to be configured manually, this feature was found primarily on ISA PnP-compatible cards. Be sure you write down or print o...