In: Categories » Electronics and communication » Batteries » Charging the Nickel Metal Hydride Battery
|
Chargers for NiMH batteries are very similar to those of the NiCd system but the electronics is generally more complex. To begin with, the NiMH produces a very small voltage drop at full charge. This NDV is almost non-existent at charge rates below 0.5C and elevated temperatures. Aging and cell mismatch works further against the already minute voltage delta. The cell mismatch gets worse with age and increased cycle count, which makes the use of the NDV increasingly more difficult. The NDV of a NiMH charger must respond to a voltage drop of 16mV or less. Increasing the sensitivity of the charger to respond to the small voltage drop often terminates the fast charge by error halfway through the charge cycle. Voltage fluctuations and noise induced by the battery and charger can fool the NDV detection circuit if set too precisely. The popularity of the NiMH battery has introduced many innovative charging techniques. Most of today’s NiMH fast chargers use a combination of NDV, voltage plateau, rate-oftemperature- increase (dT/dt), temperature threshold and timeout timers. The charger utilizes whatever comes first to terminate the fast-charge. NiMH batteries which use the NDV method or the thermal cut-off control tend to deliver higher capacities than those charged by less aggressive methods. The gain is approximately 6 percent on a good battery. This capacity increase is due to the brief overcharge to which the battery is exposed. The negative aspect is a shorter cycle life. Rather than expecting 350 to 400 service cycles, this pack may be exhausted with 300 cycles. Similar to NiCd charge methods, most NiMH fast-chargers work on the rate-of-temperature increase (dT/dt). A temperature raise of 1°C (1.8°F) per minute is commonly used to terminate the charge. The absolute temperature cut-off is 60°C (140°F). A topping charge of 0.1C is added for about 30 minutes to maximize the charge. The continuous trickle charge that follows keeps the battery in full charge state. Applying an initial fast charge of 1C works well. Cooling periods of a few minutes are added when certain voltage peaks are reached. The charge then continues at a lower current. When reaching the next charge threshold, the current steps down further. This process is repeated until the battery is fully charged. Known as ‘step-differential charge’, this charge method works well with NiMH and NiCd batteries. The charge current adjusts to the SoC, allowing high current at the beginning and more moderate current towards the end of charge. This avoids excessive temperature buildup towards the end of the charge cycle when the battery is less capable of accepting charge. NiMH batteries should be rapid charged rather than slow charged. The amount of trickle charge applied to maintain full charge is especially critical. Because NiMH does not absorb overcharge well, the trickle charge must be set lower than that of the NiCd. The recommended trickle charge for the NiMH battery is a low 0.05C. This is why the original NiCd charger cannot be used to charge NiMH batteries. The lower trickle charge rate is acceptable for the NiCd. It is difficult, if not impossible, to slow-charge a NiMH battery. At a C-rate of 0.1C and 0.3C, the voltage and temperature profiles fail to exhibit defined characteristics to measure the full charge state accurately and the charger must depend on a timer. Harmful overcharge can occur if a partially or fully charged battery is charged on a charger with a fixed timer. The same occurs if the battery has lost charge acceptance due to age and can only hold 50 percent of charge. A fixed timer that delivers a 100 percent charge each time without regard to the battery condition would ultimately apply too much charge. Overcharge could occur even though the NiMH battery feels cool to the touch. Some lower-priced chargers may not apply a fully saturated charge. On these economy chargers, the full-charge detection may occur immediately after a given voltage peak is reached or a temperature threshold is detected. These chargers are commonly promoted on the merit of short charge time and moderate price.
|
legal disclaimer
1) Our website is not responsible for the information contained by this article as well for any and all copyright infringements by authors and writers. E-articles is a free information resource. If you suspect this article for any copyright infringements, please read the Terms of service and contact us to investigate the problem.
2) The E-articles directory team is not responsible for inaccuracies, falsehoods, or any other types of misinformation this tutorial may contain and will not be liable for any loss or damage suffered by a user through the user's reliance on the information gained here. Please read the Terms of service
Useful tools and features
If you like this article (tutorial), please link to it from your web page using the information above. Linking to this page, this is the only way to help us improve our service, the same time providing your visitors with a way to improve their online experience.
related articles
Some charger manufacturers claim amazingly short charge times of 30 minutes or less. With well-balanced cells and operating at moderate room temperatures, NiCd batteries designed for fast charging can indeed be charged in a very short time. This is done by simply dumping in a high charge current during the first 70 percent of the charge cycle. Some NiCd batteries can take as much a 10C, or ten times the rated current. Precise SoC detection and temperature monitoring are essential. The high charge current must...
|
|
The idea of recharging alkaline batteries is not new. Although not endorsed by manufacturers, ordinary alkaline batteries have been recharged in households for many years. Recharging these batteries is only effective, however, if the cells have been discharged to less than 50 percent of their total capacity. The number of recharges depends solely on the depth of discharge and is limited to a few at best. With each recharge, less capacity can be reclaimed. There is a cautionary advisory, however: charging ordinary alk...
3. Types of Chargers
There are two distinct varieties of chargers: the personal chargers and the industrial chargers. The personal charger is sold in attractive packaging and is offered with such products as mobile phones, laptops and video cameras. These chargers are economically priced and perform well when used for the application intended. The personal charger offers moderate charge times. In comparison, the industrial charger is designed for employee use and accommodates fleet batteries. These chargers are built for repetit...
4. Advantages and disadvantages of the Nickel Metal Hydride (NiMH) Battery
Research of the NiMH system started in the 1970s as a means of discovering how to store hydrogen for the nickel hydrogen battery. Today, nickel hydrogen batteries are mainly used for satellite applications. They are bulky, contain high-pressure steel canisters and cost thousands of dollars each. In the early experimental days of the NiMH battery, the metal hydride alloys were unstable in the cell environment and the desired performance characteristics could not be achieved. As a result, the development of th...
5. Advantages and disadvantages of the Nickel Cadmium (NiCd) Battery
Alkaline nickel battery technology originated in 1899, when Waldmar Jungner invented the NiCd battery. The materials were expensive compared to other battery types available at the time and its use was limited to special applications. In 1932, the active materials were deposited inside a porous nickel-plated electrode and in 1947, research began on a sealed NiCd battery, which recombined the internal gases generated during charge rather than venting them. These advances led to the modern sealed NiCd battery, which is ...
6. Advantages and Disadvantages of Supercapacitor
The supercapacitor resembles a regular capacitor with the exception that it offers very high capacitance in a small size. Energy storage is by means of static charge. Applying a voltage differential on the positive and negative plates charges the supercapacitor. This concept is similar to an electrical charge that builds up when walking on a carpet. Touching an object at ground potential releases the energy. The supercapacitor concept has been around for a number of years and has found many niche applications. ...
7. Charging the Lithium Ion Battery
The Li-ion charger is a voltage-limiting device similar to the lead acid battery charger. The difference lies in a higher voltage per cell, tighter voltage tolerance and the absence of trickle or float charge when full charge is reached. While the lead acid battery offers some flexibility in terms of voltage cut-off, manufacturers of Li-ion cells are very strict on setting the correct voltage. When the Li- ion was first introduced, the graphite system demanded a charge voltage limit of 4.10V/cell. Although higher vol...
8. Advantages and Limitations of the Lithium Polymer Battery
The Li-polymer differentiates itself from other battery systems in the type of electrolyte used. The original design, dating back to the 1970s, uses a dry solid polymer electrolyte only. This electrolyte resembles a plastic-like film that does not conduct electricity but allows an exchange of ions (electrically charged atoms or groups of atoms). The polymer electrolyte replaces the traditional porous separator, which is soaked with electrolyte. The dry polymer design offers simplifications with respect to fabrica...
9. Advantages and disadvantages of the Lead Acid Battery
Invented by the French physician Gaston Planté in 1859, lead acid was the first rechargeable battery for commercial use. Today, the flooded lead acid battery is used in automobiles, forklifts and large uninterruptible power supply (UPS) systems. During the mid 1970s, researchers developed a maintenance-free lead acid battery, which could operate in any position. The liquid electrolyte was transformed into moistened separators and the enclosure was sealed. Safety valves were added to allow venting of gas...
10. The Lithium Ion Battery
Pioneer work with the lithium battery began in 1912 under G.N. Lewis but it was not until the early 1970s that the first non-rechargeable lithium batteries became commercially available. Attempts to develop rechargeable lithium batteries followed in the 1980s, but failed due to safety problems. Lithium is the lightest of all metals, has the greatest electrochemical potential and provides the largest energy density per weight. Rechargeable batteries using lithium metal anodes (negative electrodes) are capabl...