In: Categories » Computers and technology » Memory Processor Motherboards and buses » Address Lines and Buses
| Each byte in DRAM is assigned a unique numeric identifier called an address, just like houses on a street. An address is an integer value. The first byte in memory is assigned an address of zero. The region of memory near address zero is known as the bottom of memory, or low memory. The region of memory near the final byte is known as high memory. The number of physical (i.e., DRAM) bytes that a processor is capable of addressing is known as the processor's physical address space. The physical address space of a processor specifies the potential number of bytes that can be addressed, not the actual number of physical bytes present. People normally don't want to spend the money necessary to populate the entire physical address space with DRAM chips. Buying 4GB of DRAM is still usually reserved for high-end enterprise servers. The physical address space of a processor is determined by the number of address lines that it has. Address lines are a set of wires connecting the processor to its DRAM chips. Each address line specifies a single bit in the address of a given byte. For example, the Intel Pentium has 32 address lines. This means that each byte is assigned a 32-bit address so that its address space consists of 232 addressable bytes (4GB). The 8088 had 20 address lines, so it was capable of addressing 220, or 1,048,576, bytes.
To access and update physical memory, the processor uses a control bus and a data bus. A bus is a collection of related wires that connect the processor to a hardware subsystem. The control bus is used to indicate if the processor wants to read from memory or write to memory. The data bus is used to ferry data back and forth between the processor and memory. When the processor reads from memory, the following steps are performed:
When the processor writes to memory, the following steps are performed:
This description is somewhat of an oversimplification. For example, the Pentium processor reads and writes data 4 bytes at a time. This is one reason why the Pentium is called a 32-bit chip. The processor will refer to its 32-bit payload using the address of the first byte (i.e., the byte with the lowest address). Nevertheless, I think the general operation is clear.
 |
legal disclaimer
1) Our website is not responsible for the information contained by this article as well for any and all copyright infringements by authors and writers. E-articles is a free information resource. If you suspect this article for any copyright infringements, please read the Terms of service and contact us to investigate the problem.
2) The E-articles directory team is not responsible for inaccuracies, falsehoods, or any other types of misinformation this tutorial may contain and will not be liable for any loss or damage suffered by a user through the user's reliance on the information gained here. Please read the Terms of service
Useful tools and features
If you like this article (tutorial), please link to it from your web page using the information above. Linking to this page, this is the only way to help us improve our service, the same time providing your visitors with a way to improve their online experience.
related articles
When upgrading an older motherboard, it is sometimes impossible to match the installed memory. Some motherboards have 30-pin and 72-pin SIMM sockets, and many have both SIMM and DIMM sockets. If the installed memory occupies all available sockets of one type, you may have to add memory of a different type. If so, consult the manual to determine supported configurations. For example, many 30/72-pin motherboards provide four 30-pin and two 72-pin sockets, but allow you to populate both 72-pin sockets only if no memory is ...
2. Guidelines when upgrading memory in Pentium II/III/IV Celeron and Athlon systems
These systems are excellent candidates for memory upgrades. Early Pentium II systems often have only 16 MB of RAM. In the price-sensitive consumer Celeron market, many early systems shipped with only 16 MB, and some Celeron systems have been sold with only 8 MB. Expanding memory to 128 MB or more is the most cost-effective upgrade you can make. When upgrading memory in one of these systems, note the following issues: Some early Pentium II and Celeron systems use EDO SIMMs or DIMMs, but most use 3.3 volt...
3. EDORAM ~ Extended Data Out RAM
In 1995, a newer type of memory called extended data out (EDO) RAM became available for Pentium systems. EDO, a modified form of FPM memory, is sometimes referred to as Hyper Page mode. EDO was invented and patented by Micron Technology, although Micron licensed production to many other memory manufacturers. EDO memory consists of specially manufactured chips that allow a timing overlap between successive accesses. The name extended data out refers specifically to the fact that unlike FPM, the data output drivers on the chip are not ...
4. Troubleshooting Memory
Memory problems can be difficult to troubleshoot. For one thing, computer memory is still mysterious to people because it is a kind of "virtual" thing that can be hard to grasp. The other difficulty is that memory problems can be intermittent and often look like problems with other areas of the system, even software. This section shows simple troubleshooting steps you can perform if you suspect you are having a memory problem. To troubleshoot memory, you first need some memory-diagnostics testing programs. You already have several, a...
5. How SIMM DIMM and RIMM memory work
Originally, systems had memory installed via individual chips. They are often referred to as dual inline package (DIP) chips because of their designs. The original IBM XT and AT had 36 sockets on the motherboard for these individual chips; then more of them were installed on the memory cards plugged into the bus slots. I remember spending hours populating boards with these chips, which was a tedious job. Besides being a time-consuming and labor-intensive way to deal with memory, DIP chips had one notorious problemthey crept out of th...
6. The evolution of Microprocessors from 1971 to the Present
It is interesting to note that the microprocessor had existed for only 10 years prior to the creation of the PC! Intel invented the microprocessor in 1971; the PC was created by IBM in 1981. Now more than 20 years later, we are still using systems based more or less on the design of that first PC. The processors powering our PCs today are still backward compatible in many ways with the 8088 that IBM selected for the first PC in 1981. November 15, 2001 marked the 30th anniversary of the microprocessor, and in those 30 years processor ...
7. RDRAM
Rambus DRAM (RDRAM) is a fairly radical memory design found in high-end PC systems from late 1999 through 2002. Intel signed a contract with Rambus in 1996 ensuring it would support RDRAM into 2001. After 2001, Intel continued to support RDRAM in existing systems, but new chipsets and motherboards primarily shifted to DDR SDRAM, and all future Intel chipsets and motherboards are being designed for either conventional DDR or the newer DDR2 standard. RDRAM standards had been proposed that will support faster processors through 2006; however, w...